* Update mqtt_eventstream.py
Remove a line setting an internal state mqtt_eventstream.initialized to True since:
1. No other platform is doing this
2. This will create an annoying entity/item in the user interface which the user will have to explicitly hide
* Update mqtt_eventstream.py
* added new platform for the Unitymedia Horizon HD Recorder
* improve connection handling of the horizon platform
* remove unneeded parameters and fix spelling in the horizon platform
* abort or raise exception if connection to the device could not be established
* remove channel/source list and SELECT_SOURCE feature
* remove useless type check after cast and use a try block instead
* abort or raise exception if reconnect to device fails
* remove protocol specific code and restructure sending logic accordingly
* fix indentation to be pep8 complaint
* remove unused methods/properties
* fix unnecessary pylint commands and use a return to abert outside of setup_platform
* directly access config values
* Added Uptime Robot sensor
* added newline at the end and corrected doclink
* Added changes form @cdce8p
* Convert to binary_sensor
* updated requirements
* moved to correct dir
* Update uptimerobot.py
Unique id for client is generated from prefix 'snapcast_client_'
and MAC address
Unique id for group is generated from prefix 'snapcast_group_'
and UUID provided by snapcast library
When Samsung TV is idle for a period of time after issued a command,
subsequent 'turn_off' command won't turn off the TV. The issue is seen
in Samsung models with websocket as discussed in #12302.
== Reproducible Steps
1. Turn on TV (either via HA or directly).
2. Issue some commands e.g. volume ups / downs.
3. Wait for ~1 minute.
4. Issue turn_off command via HA. TV won't turn off.
5. Issue subsequent turn off commands won't turn off TV still.
6. However, issue some other commands e.g. volume ups / downs multiple
times in a row and then turn_off will turn off the TV.
== Root Cause
The underlying websocket connection opened by samsungctl get closed
after some idle time. There was no retry mechanism so issued commands
would intermittently fail but the subsequent one would succeed when
`_remote` get recreated. With `turn_off()`, however, there is an
additional call to `self.get_remote().close()` which indirectly caused
new connection to be created and then closed immediately. This causes the
component to stuck in failure mode when turn_off command is repeatly
issued.
== The Fix
Recreate the connection and retry the command if connection is closed
to avoid silent failures due to connection closed. Also set `_remote`
to None after calling close() to put it in correct state.
This fix eliminates intermittent command failure and failure mode in
turn_off().
* fixed tests: using correct camera configuration now and error handling tests must be separated out to ensure that the setup_component call is actually executed
* better error handling during setup; raising PlatformNotReady in likely recoverable cases; added tests
* reviewing this code min_temp and max_temp are always present and always in celsius
* revert change (preserve unit conversion)
* revert (due to unit conversion)
* self
* clean
* cleaner
* Hass configuration name is optional
* Check explicitly if name is none
* Reverted back to old logic for zones configured in configuration.yaml, where many zones can have the same name
* New test to verify use case of allowing multiple zones having the same name
* Fix too long line
* Add set_default_service to logger
* Fix 2-line lint error
* Add set_default_level to services.yaml
* Add tests for set_default_level
* Remove function and add else when setting default
Right now, "Hub Status" is very generic, I didn't know what component it was coming from, and the only way to tell was searching the source code to find the reference.
* Initial version of wirelesstags platform support.
* Pinned wirelesstagpy, generated requirements_all.
* Fixed temperature units in imperial units systems, make binary events more tags specific.
* Lowercased tag name during entity_id generation.
* Fixed: tag_id template for tag_binary_events, support of light sensor for homebridge.
* Minor style cleanup.
* Removed state, define_name, icon. Reworked async arm/disarm update. Removed static attrs. Introduced available property. Custom events contains components name now. Cleaned dedundant items from schema definition.
* Removed comment and beep duration from attributes. Minor cleanup of documentation comment.
* Ignoring Wemo switches linked in iOS app.
* Reworked passing data from platform to components using signals.
This commit adds a new history component for the IBM Watson IoT
Platform. The IBM Watson IoT Platform allows for tracking of devices
and analytics on top of the device data. This new component allows
users to have home assistant automatically populate a watson iot
platform board with device data from devices managed by home assistant.
* Media player: general sound mode support
* General sound mode support
* White spaces
* Add sound mode support to demo media player
* white space
* remove unnessesary code
