* rename channel -> cluster handler
* remove refs to channels and create endpoint class
* remove remaining references to channels
* fix filter
* take in latest changes from #91403
* missed one
* missed a reference
* Adding binding of IKEA Matter Switch cluster
IKEA Symfonisk Gen 2 is using Matter ZCL Switch command but on manufacture cluster then its not supported in ZVL R8 that need being bond for sending the commands to the coordinator.
* Update manufacturerspecific.py
* Update manufacturerspecific.py
Delete not needed function `@registries.BINDABLE_CLUSTERS.register(0xFC80)`
* Construct binary sensor state from zigpy cache (WIP)
* Workaround zha-quirks issue where "MotionWithReset" quirks don't update attribute cache (WIP)
zha-quirks currently has an issue where the ZONE_STATE attribute is updated (when the zone_STATUS changes).
https://github.com/zigpy/zha-device-handlers/pull/2231 is a proper fix for this.
For now, we just update the attribute cache when we get the "zone status update notification" command.
This wasn't noticed before, as the "attribute report signal" was sent from the `cluster_command()` method and the used the provided attribute (in the signal) to update the `_state` value in the binary sensor class.
As we just tell HA to write state again when we get an attribute report now, the ZONE_STATUS attribute is read now (and needs to be correct).
* Use parse() method of main class for IasZone entity (with stripped bits)
* Change wording in comment, remove explicitly sending attr signal
(This comment should be removed/changed later anyway)
* Remove note
* Get zone_status attribute id with zigpy
* Remove `security.` prefix for `IasZone` import
`AceCluster` was already directly imported and `IasZone` is too now for getting the attribute id
* Store full zone status attribute in cache
* Check that non-alarm bits are ignored in IasZone sensor test
* Re-enable occupancy binary sensor test
This test seems to work fine and I don't see any reason why it was commented out for a while
* Fix cached read mix-up for `zone_status`/`zone_state`
This allows cached reads for `zone_state` (enrolled or not), but forces a new read for `zone_status` (alarm or not).
* Rename `zha.api` to `zha.websocket_api`
* Implement a ZHA network settings API
* Use the enum name as the radio type
* Don't filter out ignored config entries
* [WIP] Start unit tests
* Add unit tests
* Rename ZHA websocket API module in `.coveragerc`
* Rename `api` to `websocket_api`
* Increase test coverage to 100%
* Use a set for config entries task tracking
* Allow adding background tasks to config entries
* Add tests for config entry add tasks
* Update docstrings on core create task
* Migrate roon and august
* Use in more places
* Guard for None
* Add options and execute_if_off_supported properties to Color channel
* Initialize "options" attribute on Color channel (allowing cache)
* Implement execute_if_off_supported for ZHA lights
* Make sure that color_channel exists, before checking execute_if_off_supported
* Replace "color_channel is not None" check with simplified "if color_channel"
* Make "test_number" test expect "options" for init attribute
* Add test_on_with_off_color test to test old and new behavior
* Experimental code to also support "execute_if_off" for groups if all members support it
* Remove support for groups for now
Group support will likely be added in a separate PR. For now, the old/standard behavior is used for groups.
* Initial "group members assume state" implementation for ZHA
* Remove left-over debug flag (where polling was disabled)
* Implement _send_member_assume_state_event() method and also use after turn_off
* Only assume updated arguments from service call to group
* Make code more readable and change checks slightly
* Move "send member assume state" events to LightGroup on/off calls
* Include new config option in tests
* Check that member is available before updating to assumed state
* Lower "update group from child delay" for debouncer to basically 0 when using assumed member state
* Allow "child to group" updates regardless of config option
This is not needed, as group members will not update their state, as long as they're transitioning. (If a group transitions, it also sets its members to transitioning mode)
This fixes multiple issues. Previously, the state of a group was completely wrong when:
- turn on group with 10 second transition
- turn on members individually
- turn off members individually
- group state would not update correctly
* Move "default update group from child delay" constant
* Change to new constant name in test
* Also update fan test to new constant name
* Decrease "update group from child delay" to 10ms
In my testing, 0.0 also works without any issues and correctly de-bounces child updates when using the "assume state option".
This is just for avoiding multiple state changes when changing the group -> children issue individual updates.
With 2 children in a group and delay 0, both child updates only cause one group re-calculation and state change.
0.01 (10ms) should be plenty for very slow systems to de-bounce the update (and in the worst case, it'll cause just another state change but nothing breaks)
* Also implement "assuming state" for effect
Not sure if anybody even uses this, but this one is a bit special because the effect is always deactivated if it's not provided in the light.turn_on call.
* Move shortened delay for "assuming members" to a constant
* Add basic test to verify that group members assume on/off state
* Move _assume_group_state function declaration out of async_added_to_hass
* Fix rare edge-case when rapidly toggling lights and light groups at the same time
This prevents an issue where either the group transition would unset the transition flag or the single light would unset the group transition status midst-transition.
Note: When a new individual transition is started, we want to unset the group flag, as we actually cancel that transition.
* Check that effect list exists, add return type
* Re-trigger CI due to timeout
* Increase ASSUME_UPDATE_GROUP_FROM_CHILD_DELAY slightly
The debouncer is used when updating group member states either by assuming them (in which case we want to barely have any delay), or between the time we get the results back from polling (where we want a slightly longer time).
As it's not easily possible to distinguish if a group member was updated via assuming the state of the group or by the polling that follows, 50 ms seems to be a good middle point.
* Add debug print for when updating group state
* Fix issues with "off brightness" when switching between group/members
This fixes a bunch of issues with "off brightness" and passes it down to the members correctly.
For example, if a light group is turned off with a transition (so bulbs get their level set to 1), this will also set the "off brightness" of all individual bulbs to the last level that they were at.
(It really fixes a lot of issues when using the "member assume group state" option. It's not really possible to fix them without that.)
Furthermore, issues where polling was previously needed to get the correct state after "playing with transitions", should now get be resolved and get correct state when using the "members assume group state" option.
Note: The only case which still can't be fixed is the following:
If individual lights have off_with_transition set, but not the group, and the group is then turned on without a level, individual lights might fall back to brightness level 1 (<- at least now shows correctly in UI even before polling).
Since all lights might need different brightness levels to be turned on, we can't use one group call. But making individual calls when turning on a ZHA group would cause a lot of traffic and thereby be counter-productive.
In this case, light.turn_on should just be called with a level (or individual calls to the lights should be made).
Another thing that was changed is to reset off_with_transition/off_brightness for a LightGroup when a member is turned on (even if the LightGroup wasn't turned on using its turn_on method).
off_with_transition/off_brightness for individual bulbs is now also turned off when a light is detected to be on during polling.
Lastly, the waiting for polled attributes could previously cause "invalid state" to be set (so mid-transition levels).
This could happen when group and members are repeatedly toggled at similar times. These "invalid states" could cause wrong "off brightness" levels if transitions are also used.
To fix this, we check after waiting for the polled attributes in async_get_state to see if a transition has started in the meanwhile. If so, the values can be discarded. A new poll will happen later and if using the "members assume group state" config option, the values should already be correct before the polling.
* Enable "group members assume state" config option by default
The config tests are also updated to expect the config option be enabled by default.
For all tests, the config option is generally disabled though:
There are only two group related tests. The one that tests this new feature overrides the config option to be enabled anyway.
The other tests works in a similar way but also "sends" attribute reports, so we want to disable the feature for that test.
(It would also run with it enabled (if the correct CHILD_UPDATE value is patched), but then it would test the same stuff as the other test, hence we're disabling the config option for that test.)
* Add tier summation delivered for zlinky
* Improve name case
* Add other tiers and register tier
* Fix smartenergy sensor update
* Account for new reporting configuration in unit tests
* Use cluster ID attributes instead of hardcoding the values
* Use tier names instead of the numeric constants for formatter
* Revert active register tier delivered
* Fix tests
Co-authored-by: puddly <32534428+puddly@users.noreply.github.com>
* Add Aqara c1 pet feeder support to ZHA
* clean up
* cleanup
* state classes for daily measurements
* cleanups
* cleanups
* restore the refreshing of the inverted value cache
* cleanup
